73 lines
2.6 KiB
C
73 lines
2.6 KiB
C
// Board and hardware specific configuration
|
|
#define MICROPY_HW_FLASH_STORAGE_BYTES (PICO_FLASH_SIZE_BYTES - (2 * 1024 * 1024))
|
|
|
|
#ifndef CYW43_WL_GPIO_COUNT
|
|
// Shim the EXT GPIOs because we can't specify a variant pins.csv
|
|
// Remap them to LED R, G and B respectively on non-W builds
|
|
#define pin_EXT_GPIO0 pin_GPIO16
|
|
#define pin_EXT_GPIO1 pin_GPIO17
|
|
#define pin_EXT_GPIO2 pin_GPIO18
|
|
#endif
|
|
|
|
// I2C0 (non-default)
|
|
#define MICROPY_HW_I2C0_SCL (PLASMA2350_SDA_PIN)
|
|
#define MICROPY_HW_I2C0_SDA (PLASMA2350_SCL_PIN)
|
|
|
|
// Set up networking.
|
|
#define MICROPY_PY_NETWORK_HOSTNAME_DEFAULT "PLASMA2350"
|
|
|
|
#if defined(MICROPY_PY_NETWORK_CYW43)
|
|
|
|
// CYW43 driver configuration.
|
|
#define CYW43_USE_SPI (1)
|
|
#define CYW43_LWIP (1)
|
|
#define CYW43_GPIO (1)
|
|
#define CYW43_SPI_PIO (1)
|
|
|
|
#define MICROPY_HW_PIN_EXT_COUNT CYW43_WL_GPIO_COUNT
|
|
|
|
#if defined(CYW43_PIN_WL_DYNAMIC)
|
|
|
|
#define CYW43_PIO_CLOCK_DIV_DYNAMIC (1)
|
|
|
|
// Defined by pimoroni_pico_plus2w_rp2350.h
|
|
//#define CYW43_DEFAULT_PIN_WL_HOST_WAKE SPICE_RESET_MOSI_PIN
|
|
//#define CYW43_DEFAULT_PIN_WL_REG_ON SPICE_TX_MISO_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_DATA_OUT CYW43_DEFAULT_PIN_WL_HOST_WAKE
|
|
#define CYW43_DEFAULT_PIN_WL_DATA_IN CYW43_DEFAULT_PIN_WL_HOST_WAKE
|
|
#define CYW43_DEFAULT_PIN_WL_CLOCK 29u
|
|
#define CYW43_DEFAULT_PIN_WL_CS 25u
|
|
|
|
/* SPICE alternative
|
|
#define CYW43_DEFAULT_PIN_WL_HOST_WAKE SPICE_RESET_MOSI_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_REG_ON SPICE_TX_MISO_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_DATA_OUT SPICE_RESET_MOSI_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_DATA_IN SPICE_RESET_MOSI_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_CLOCK SPICE_NETLIGHT_SCK_PIN
|
|
#define CYW43_DEFAULT_PIN_WL_CS SPICE_RX_CS_PIN
|
|
*/
|
|
|
|
// Slow down the wireless clock, since we'll be running
|
|
// comms through wiring spaghetti!
|
|
#define CYW43_PIO_CLOCK_DIV_INT 50
|
|
#define CYW43_PIO_CLOCK_DIV_FRAC 0
|
|
#define CYW43_SPI_PROGRAM_NAME spi_gap0_sample1
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
// Might be defined in mpconfigvariant_PPP.cmake
|
|
// This is not checked by mpconfigport.h so we must set up networking below
|
|
#if defined(MICROPY_PY_NETWORK_PPP_LWIP)
|
|
|
|
// Nothing to do here?
|
|
|
|
#endif
|
|
|
|
// If a variant is not used, define a fallback board name
|
|
#ifndef MICROPY_HW_BOARD_NAME
|
|
|
|
#define MICROPY_HW_BOARD_NAME "Pimoroni Plasma 2350"
|
|
|
|
#endif |